Rod seals factory manufacturer 2024: Mechanical seals are engineered for most pumps, mixer and agitator applications in maintenance. In many cases the designs have been proven to be workhorses over years of use. In others seals must be designed for evolving industrial demands. The basic rotating face mechanical seal design is adaptable to serve a wide range of sealing applications including compressors. Standard mechanical seals can suit most requirements to temperatures of 500 degrees F and shaft speeds to 3600 RPM. The selection of secondary seal type often determines the temperature and chemical capabilities of the seal. The combination of materials used in the rotating and stationary faces define the abrasive resistance, and chemical resistance. Seal face combinations will also determine the amount of energy consumed by the pump, mixer, agitator or compressor. Seal faces can be balanced to permit higher pressure sealing. Balanced seals can seal pressures above 200 psi, or used in a multiple stages for higher pressures or especially severe fluid services. Special mechanical seals can be furnished to meet the most demanding of industrial applications considering pressure, temperature, speed or fluid. See extra info at spring seals.

Basics of fluid pump sealing – A mechanical seal is simply a method of containing fluid within a vessel (typically pumps, mixers, etc.) where a rotating shaft passes through a stationary housing or occasionally, where the housing rotates around the shaft. When sealing a centrifugal pump, the challenge is to allow a rotating shaft to enter the ‘wet’ area of the pump, without allowing large volumes of pressurized fluid to escape. To address this challenge there needs to be a seal between the shaft and the pump housing that can contain the pressure of the process being pumped and withstand the friction caused by the shaft rotating. The gap between the faces on a typical seal is as little as 1 micron – 75 times narrower than a human hair. Because the gap is so tiny, particles that would otherwise damage the seal faces are unable to enter, and the amount of liquid that leaks through this space is so small that it appears as vapor – around ½ a teaspoon a day on a typical application.

The gasket made by DMS SEALS is uniquely mechanical and thermally stable and it has excellent oxidation resistance. Compared with other thermoplastics, it can be applied to components such as valves and bushings, with higher wear resistance, higher mechanical properties and thermal fatigue resistance. At the same time, it has excellent oil resistance (alkane oil), heat resistance, water resistance, aging resistance, air tightness and excellent adhesion. It is commonly used in media such as water, oil, and natural gas.

The rod seal is the most important sealing component designed by DMS SEALS in the liquid sealing application. It can effectively prevent the liquid inside the cylinder from leaking to the outside. Moreover, if there is a leakage problem in the rod seal, the performance of the equipment will be degraded. There are even some machine and human safety issues in extreme cases. This type of seal meets the standards of GB/T 15242.1-94 and GB/T 15242.3-94. It is ideal for high and low-speed reciprocating rods and rods in high-pressure system cylinders. Moreover, it can be used in a variety of fluids and high-temperature environments. It is characterized by its high corrosion resistance and its ability to work well in a corrosive media with no oil spots. It has high stability under pressure and harsh conditions. The outstanding advantages of our seals are strong wear resistance, resistance to extrusion, low friction and no stick-slip.

Gasket sealing mechanism: The function of the gasket is caused by the blocking effect on the internal medium formed by the contact pressure of the sealing material on the joint surface and the elastic restoring force to the external tightening force. Classification and structure of gaskets: Gaskets are divided into three categories: non-metallic gaskets, non-metallic and metal combined gaskets and metal gaskets. The common materials are rubber, leather, asbestos board, cork, PTFE, tinplate, steel, aluminum, copper and stainless steel.

Support and positioning The piston and piston rod are radially supported and positioned in the cylinder barrel. Isolate the two pairs of motion pairs of piston and cylinder, piston rod and guide sleeve to prevent direct scratches, abrasions and strains between the motion pairs. Especially when the motion pairs are all steel parts, they must be isolated, otherwise they will be easily strained. The guide belt also has an important role to reduce the friction and friction work between the moving parts, reduce the ineffective work and heat. Vibration absorption and noise reduction Reduce system vibration and noise. It is mainly filled with tetrafluoroethylene and phenolic cloth, and there are also a very small amount of polyoxymethylene, nylon and soft metal. Read more information on https://www.dmsseals.com/.

DMS Seals is a scientific and technical mechanical seal manufacturer and oil seal supplier specializing in seal production, sealing material development, and the conception of sealing solutions for special working conditions. We have 120 employees, including 70 senior technicians. DMS Seals has a number of invention patents and leading production processes. The R&D team is able to design and develop Rubber Seal & Hydraulic Seals for various mechanical sealing systems under complex conditions. We have already passed the certification of ISO 9001 and TS 16949.

Construction machinery sealing system requirements: High and low temperature resistance Because of continuous work for a long time, if it is outdoors in summer, the hydraulic oil temperature of the machine may exceed 100°C, which requires the seal to be resistant to high temperature. If it is outdoors in winter, the temperature may be around -40°C when it is just turned on, and the seals are required to be resistant to low temperatures. Therefore, the sealing system is required to withstand a wide temperature range. The machine itself walks. Due to the limitation of volume and weight, the hydraulic oil tank is generally relatively small.

The bearing seal maintains lubrication where needed and helps protect the working part from abrasive particles and corrosive moisture. The seals are precisely configured to provide extremely low friction and excellent contamination resistance. It is perfect for high speed or low torque equipment as well as dusty environments. Moreover, the seal is reasonably designed to provide superior resistance to foreign particles.